Refillable – SRA #312 Soldering Flux Pen Low-Solids, No-Clean 10ml

#ad
SRA PEN-NC #ad - If removal of the residue is needed then it can be cleaned with warm water. Contains 10 ml of No-Clean Low Solids Flux. Compatible with Lead and Lead-Free Solders. This is the first environmentally friendly Flux Pen that can be refilled for a cost effective flux solution. This flux was designed for soldering high quality electronic printed circuit boards PCBs, such as, mixed technology, through-hole, and surface mount assemblies while eliminating the need for a post cleaning operation.

Superior fluxing ability with Instant wetting Made in the USA This flux is free of any halides, resin, or rosin. Suitable for automotive, computer, telecom. Environmentally Friendly Refillable Pen. Flux conforms to ipc-ansi-j-stD-004, Type ORL0 Residues are Non-Corrosive and Non-Conductive. This product is rohs compliant for rework and touch-up of SMT, SMD, and through hole solder joints.

More information about SRA PEN-NC #ad

Thermaltronics FBA_TMT-TC-2 Lead Free Tip Tinner, 20 g in 0.8 oz. Container

#ad
Thermaltronics FBA_TMT-TC-2 #ad - Lead free RoHS Compliant. Thermaltronics tmt-tc-2 tip tinners is a compressed tablet of pure tin and ammonia phosphate formulation in a metal container with lid. Minimal residues. Removes tip oxidation. Thermaltronics tmt-tc-2 tip tinners provides fast, efficient cleaning and re-tinning of blackened and highly oxidized soldering iron tips, safely and efficiently.

Rapidly re-tins badly oxidised soldering iron tips. It has a self adhesive pad on the underside to allow it to be affixed on, or near the work station. No-clean compatible formulation.

More information about Thermaltronics FBA_TMT-TC-2 #ad


Similar products:


Hakko 599B-02 Wire-type soldering iron tip cleaner

#ad
American Hakko Products, Inc 599B-02 #ad - No water required. Rapidly re-tins badly oxidised soldering iron tips. These sponges are hard enough to remove debris and some corrosion from the solder tips while being soft enough not to damage the tip. Lead free RoHS Compliant. Cleans better than conventional sponges. Removes tip oxidation. The hakko 599b-02 is a replacement solder tip cleaning wire sponge.

No-clean compatible formulation. No contamination risk compared to conventional tip tinners. They help to remove oxides and excess solder to preserve tip life and enable clean, precise soldering. Does not cause premature wear of soldering iron tips. Will not reduce the tip temperature. Minimal residues.

More information about American Hakko Products, Inc 599B-02 #ad


Similar products:


NTE Electronics SW02-10 No-Clean Solder Wick, #4 Blue, .098" Width, 10' Length

#ad
NTE Electronics, Inc. SW02-10 #ad - Nte solder wick is made from fine copper wire woven together with a no-clean flux formula added to it to increase absorption. No water required. Cleans better than conventional sponges. Lead free RoHS Compliant. No-clean compatible formulation. No contamination risk compared to conventional tip tinners. Does not cause premature wear of soldering iron tips.

Will not reduce the tip temperature. Removes tip oxidation. Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes. Rapidly re-tins badly oxidised soldering iron tips. Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board.

NTE Electronics SW02-10 No-Clean Solder Wick, #4 Blue, .098" Width, 10' Length #ad - Minimal residues. 100% copper wick has fine braid design to promote strong capillary action to pull in excess solder. Available with standard or anti-static bobbins.

More information about NTE Electronics, Inc. SW02-10 #ad


Similar products:


CHP-170 Micro Cutter

#ad
Quality Hand Tools CHP-170 #ad - The tool is constructed of 2. 5mm heat-treated carbon steel that provides durability and long life. Flush-cut micro soft-wire cutter has 8mm long jaw with angled head for flush-cutting applications on up to 16 gauge 1. 3mm copper and soft wire. No-clean compatible formulation. An internal spring returns the tool to the open position, reducing operator fatigue.

21-degree. Precision-ground holes and surfaces provide smooth movement, and spring returns tool to open position to reduce operator fatigue. Cleans better than conventional sponges. No water required. Available with standard or anti-static bobbins. Removes tip oxidation. Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board.

CHP-170 Micro Cutter #ad - Rapidly re-tins badly oxidised soldering iron tips. Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes. No contamination risk compared to conventional tip tinners. Does not cause premature wear of soldering iron tips. Parkerized surfaces prevent glare and increase corrosion resistance.

More information about Quality Hand Tools CHP-170 #ad


Similar products:


SRA #312 No-Clean Flux Refill for Flux Pen

#ad
SRA #80 #ad - Rapidly re-tins badly oxidised soldering iron tips. Cleans better than conventional sponges. This is a refill for the first environmentally friendly Flux Pen that can be refilled for a cost effective flux solution. Superior fluxing ability with Instant wetting This flux is free of any halides, resin, or rosin.

Will not reduce the tip temperature. Does not cause premature wear of soldering iron tips. Dolphin-style nonslip hand grips with curved fore-edge provide comfort and control, and Parkerized surfaces prevent glare and increase corrosion resistance. No-clean compatible formulation. If removal of the residue is needed then it can be cleaned with warm water.

SRA #312 No-Clean Flux Refill for Flux Pen #ad - Flux conforms to ipc-ansi-j-stD-004, Type ORL0 This product is rohS Compliant Lead free RoHS Compliant. Contains 50 ml of No-Clean Low Solids Flux. 21-degree. Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes. Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board.

More information about SRA #80 #ad


Similar products:


MG Chemicals #3 No Clean Super Wick Desoldering Braid, 0.075" Width x 5' Length, Green

#ad
MG Chemicals 425-NS #ad - No water required. Static free bobbins. Suitable for automotive, computer, telecom. Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board. Will not reduce the tip temperature. No clean super wick. No contamination risk compared to conventional tip tinners. Contains 50 ml of No-Clean Low Solids Flux.

Dolphin-style nonslip hand grips with curved fore-edge provide comfort and control, and Parkerized surfaces prevent glare and increase corrosion resistance. Nsf - nonfood compounds program Listed P1, Nsf Registration #154374. Flux residue remaining on board does not have to be cleaned. No clean super wick. Flux residue is non-conductive and non-corrosive.

MG Chemicals #3 No Clean Super Wick Desoldering Braid, 0.075" Width x 5' Length, Green #ad - No-clean compatible formulation. For rework and touch-up of SMT, SMD, and through hole solder joints. Flux residue remaining on board does not have to be cleaned. 100% copper wick has fine braid design to promote strong capillary action to pull in excess solder. Cleans better than conventional sponges.

More information about MG Chemicals 425-NS #ad


Similar products:


No Clean Lead Free Low Temperature Solder Paste 15 Grams

#ad
Hardware & Outdoor 247-LOWTEMP-15 #ad - Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes. Dolphin-style nonslip hand grips with curved fore-edge provide comfort and control, and Parkerized surfaces prevent glare and increase corrosion resistance. Flux residue remaining on board does not have to be cleaned.

Contains 50 ml of No-Clean Low Solids Flux. Does not cause premature wear of soldering iron tips. Minimal residues. 2. 5mm heat-treated carbon steel construction provides durability and long life. Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board. Compatible with Lead and Lead-Free Solders.

No Clean Lead Free Low Temperature Solder Paste 15 Grams #ad - For rework and touch-up of SMT, SMD, and through hole solder joints. Contains Silver for less brittle joint. Nsf - nonfood compounds program Listed P1, Nsf Registration #154374. 21-degree. 100% copper wick has fine braid design to promote strong capillary action to pull in excess solder. No contamination risk compared to conventional tip tinners.

More information about Hardware & Outdoor 247-LOWTEMP-15 #ad


Similar products:


Gikfun DIY SMD SMT Welding Practice Soldering Skill Training Board Led EK7026_

#ad
Esooho LYSB00Y20JYTM-ELECTRNCS #ad - No water required. 21-degree. Contains Silver for less brittle joint. High sir-meets the requirements of both the bellcore specification TR-TSY-000078 and IPC test method III. Low melting Point Solder Paste. Rapidly re-tins badly oxidised soldering iron tips. Nsf - nonfood compounds program Listed P1, Nsf Registration #154374.

The welding product is a beautiful water lamp circuit. The back of the board with mm/Inch ruler, Easy to measure component. Minimal residues. Compatible with Lead and Lead-Free Solders. It's diy kits, Red Led. You can quickly judge the welding effect. Precision-ground holes and surfaces provide smooth movement, and spring returns tool to open position to reduce operator fatigue.

Gikfun DIY SMD SMT Welding Practice Soldering Skill Training Board Led EK7026_ #ad - You can quickly judge the welding effect. Available with standard or anti-static bobbins. Contains 50 ml of No-Clean Low Solids Flux. No-clean compatible formulation. Cleans better than conventional sponges.

More information about Esooho LYSB00Y20JYTM-ELECTRNCS #ad


Similar products:


Tabiger Solder Wick & Desoldering Pump, Solder Sucker & Desoldering Wick, 2pcs Solder Braid 2.5mm Width, 1.5m Length- Desoldering Vacuum Pump Solder Remover

#ad
TABIGER #ad - Tabiger solder sucker & solder wickit's a must-have tool for electronics kit, while the solder wick used in small, you can use them together,solder sucker for large amounts, hard to reach areas. How to use the solder sucker:◆step 1: press the plunger down until you hear a click sound;◆step 2: Heat up solder around item to be removed by using a soldering iron;◆Step 3: When the solder is liquid, place the tip of the solder sucker next to the liquid and press press the trigger;◆Step 4: Repeat this process if necessary.

How to use the desoldering wick:◆step 1: place the wick over the solder you need to be removed and then just push the heated soldering iron tip onto the wick; ◆Step 2: Remove the wick once the solder has been absorbed; ◆Step 3: Cut off the used part of the wick; ◆Step 4: Repeat this process if needed.

Tabiger Solder Wick & Desoldering Pump, Solder Sucker & Desoldering Wick, 2pcs Solder Braid 2.5mm Width, 1.5m Length- Desoldering Vacuum Pump Solder Remover #ad - Package included:1* solder Sucker2* Solder Wick Lead free RoHS Compliant. Flush-cut micro soft-wire cutter has 8mm long jaw with angled head for flush-cutting applications on up to 16 gauge 1. 3mm copper and soft wire. You can quickly judge the welding effect. After welding, just connect electricity 3-12V to see the effect.

Contains 50 ml of No-Clean Low Solids Flux. Available with standard or anti-static bobbins.

More information about TABIGER #ad


Similar products:


Aven 17010 Adjustable Circuit Board Holder

#ad
Aven 17010 #ad - With english manual in the package. Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes. The base of this rigid metal stand features four rubber feet to ensure stability. For rework and touch-up of SMT, SMD, and through hole solder joints.

Retractable to accommodate various board sizes up to 198mm wide and up to 4mm thick. Precision-ground holes and surfaces provide smooth movement, and spring returns tool to open position to reduce operator fatigue. 137c 278f melting Point Eutectic. T4 new industry standard. Will not reduce the tip temperature.

Aven 17010 Adjustable Circuit Board Holder #ad - Cleans better than conventional sponges. Compatible with Lead and Lead-Free Solders. Does not cause premature wear of soldering iron tips. 2. 5mm heat-treated carbon steel construction provides durability and long life. Two dispensing tips 16g and 20g. High sir-meets the requirements of both the bellcore specification TR-TSY-000078 and IPC test method III.

Flux residue is non-conductive and non-corrosive.

More information about Aven 17010 #ad


Similar products: